Whisky Parts Co. Tubeless Rim Tape.
Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
SRAM's Conversion Caps are just what you need to convert your Roam 60, 50, or Rail 50 wheels to fit your bike's rear axle.
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Origin-8's Track Cog Lock Ring with left-handed threading and 1.29 x 24tpi in a chrome finish completes your basic track cog locking needs.
On today's MTB frames, there are many diameters and width dropouts standards. Most Mavic wheels can be fitted with specific adapters to match with those frames: 142mm extenders for ITS-4 hubs, 142 mm extenders for TS-2 hubs and QR adapters (delivered with a front quick release) for all of them. - Converts a 12mm rear axle to fit in a frame with 9.5mm dropouts - Requires one pair per hub
Mavic's XD freehub body is compatible with all Crossmax and Deemax wheels (2012 and after) or all wheels using TS-2 hubs. This freehub body converts a rear wheel to work with SRAM's XD standard, making the wheel compatible with the XX1 drivetrain. Two kits are available : XD freehub body ITS-4 and XD freehub body TS-2, each with hub-specific parts.
Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.
The buyer's choice for wheel builders looking to save weight. ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond. - 32 nipples weigh approximately 30 grams
Page 1 of 1